????

Your IP : 52.15.174.103

Current Path : C:/Windows/System32/drivers/en-US/
Upload File :
Current File : C:/Windows/System32/drivers/en-US/serial.sys.mui

MZ����@���	�!�L�!This program cannot be run in DOS mode.

$��<߱�R���R���R�U�����R�U�P���R�Rich��R�PEL�!(

P��@ d$8.rdata�@@.rsrc0 &@@|���
T88|���$��8.rdata8x.rdata$zzzdbg �.rsrc$01� �#.rsrc$02 �'0ok��o��Z{}���þ��-���e|�����(�@�X�p�����	�	�	�� ���!4��@��MUI���'d�O%��v3er�'"4��7�܋�
Q���xHF���MUIen-US@@X"@"@(���*�+���!�4#�)�(,�-��\The kernel debugger is already using %2.

�While validating that %2 was really a serial port, a fifo was detected. The fifo will be used.

�User configuration data for parameter %2 overriding firmware configuration data.

tDisabling %2 as requested by the configuration data.

`Unable to create the symbolic link for %2.

dUnable to create the device map entry for %2.

dUnable to delete the device map entry for %2.

�There is a serial mouse using the same interrupt as %2.  Therefore, %2 will not be started.

�There was a serial mouse found on %2.  Therefore, %2 will be assigned to the mouse.

�Another driver on the system, which did not report its resources, has already claimed the interrupt used by %2.

pNot enough resources were available for the driver.

�The baud clock rate configuration is not supported on device %2.

�The hardware locations for %2 could not be translated to something the memory management system could understand.

�The hardware resources for %2 are already in use by another device.

�No memory could be allocated in which to place new data for %2.

�While validating that %2 was really a serial port, the interrupt enable register contained enabled bits in a must be zero bitfield.

The device is assumed not to be a serial port and will be deleted.

�While validating that %2 was really a serial port, the modem control register contained enabled bits in a must be zero bitfield.

The device is assumed not to be a serial port and will be deleted.

�While validating that %2 was really a serial port, the interrupt id register contained enabled bits in a must be zero bitfield.

The device is assumed not to be a serial port and will be deleted.

dWhile validating that %2 was really a serial port, the baud rate register could not be set consistantly.

The device is assumed not to be a serial port and will be deleted.

xSome firmware configuration information was incomplete.

�No Parameters subkey was found for user defined data.  This is odd, and it also means no user configuration can be found.

pSpecific user configuration data is unretrievable.

�On parameter %2 which indicates a multiport card, must have a port index specified greater than 0.

�On parameter %2 which indicates a multiport card, the port index for the multiport card is too large.

\The bus type for %2 is not recognizable.

xThe bus type for %2 is not available on this computer.

�The bus specified for %2 does not support the specified method of interrupt.

lUser configuration for parameter %2 must have %3.

�The user specified port for %2 is way too high in physical memory.

�The status port for %2 is way too high in physical memory.

�The status port for %2 overlaps the control registers for the device.

�The control registers for %2 overlaps with the %3 control registers.

�The status register for %2 overlaps the %3 control registers.

�The status register for %2 overlaps with the %3 status register.

�The control registers for %2 overlaps the %3 status register.

�Two ports, %2 and %3, on a single multiport card can't have two different interrupts.

tParameter %2 data is unretrievable from the registry.

�While validating that %2 was really a serial port, the contents of the divisor latch register was identical to the interrupt enable and the receive registers.

The device is assumed not to be a serial port and will be deleted.

xCould not translate the user reported I/O port for %2.

�Could not get the user reported interrupt for %2 from the HAL.

�Could not translate the user reported Interrupt Status Register for %2.

�Could not report the discovered legacy device %2 to the IO subsystem.

HError writing to the registry.

�Could not report device %2 to IO subsystem due to a resource conflict.

�The serial driver detected a hardware failure on device %2 and will disable this device.

�4VS_VERSION_INFO��
|O
|O?�StringFileInfo�040904B0LCompanyNameMicrosoft CorporationRFileDescriptionSerial Device Driverh$FileVersion10.0.20348.1 (WinBuild.160101.0800)6InternalNameserial.sys�.LegalCopyright� Microsoft Corporation. All rights reserved.FOriginalFilenameserial.sys.muij%ProductNameMicrosoft� Windows� Operating System>
ProductVersion10.0.20348.1DVarFileInfo$Translation	�PADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPAD