????

Your IP : 216.73.216.152


Current Path : C:/Windows/System32/en-US/
Upload File :
Current File : C:/Windows/System32/en-US/arp.exe.mui

MZ����@���	�!�L�!This program cannot be run in DOS mode.

$��<߱�R���R���R�U�����R�U�P���R�Rich��R�PEL�!

@�@ �8.rdata�@@.rsrc  @@�X�
T88�X�$��8.rdata8x.rdata$zzzdbg �.rsrc$01� �.rsrc$02 �q���2<B4�Y">ҰW�
��<O_�X���(�@�X�p�����	�	�	�� ���!d�4|�MUI�����d�sF���Q�7K5��A�#n-%m�X`���MUIen-US'''$'��


Displays and modifies the IP-to-Physical address translation tables used by

address resolution protocol (ARP).



ARP -s inet_addr eth_addr [if_addr]

ARP -d inet_addr [if_addr]

ARP -a [inet_addr] [-N if_addr] [-v]



  -a            Displays current ARP entries by interrogating the current

                protocol data.  If inet_addr is specified, the IP and Physical

                addresses for only the specified computer are displayed.  If

                more than one network interface uses ARP, entries for each ARP

                table are displayed.

  -g            Same as -a.

  -v            Displays current ARP entries in verbose mode.  All invalid 

                entries and entries on the loop-back interface will be shown.

  inet_addr     Specifies an internet address.

  -N if_addr    Displays the ARP entries for the network interface specified

                by if_addr.

  -d            Deletes the host specified by inet_addr. inet_addr may be 

                wildcarded with * to delete all hosts.

  -s            Adds the host and associates the Internet address inet_addr

                with the Physical address eth_addr.  The Physical address is

                given as 6 hexadecimal bytes separated by hyphens. The entry

                is permanent.

  eth_addr      Specifies a physical address.

  if_addr       If present, this specifies the Internet address of the

                interface whose address translation table should be modified.

                If not present, the first applicable interface will be used.

Example:

  > arp -s 157.55.85.212   00-aa-00-62-c6-09  .... Adds a static entry.

  > arp -a                                    .... Displays the arp table.

@ARP: bad IP address: %2!S!.

<ARP: bad argument: %2!S!

�

Interface: %1!S!

  Internet Address      Physical Address      Type

8ARP: not enough memory

other%0

invalid%0

dynamic%0

static%0

lARP: Windows Sockets initialization failed: %2!d!

PThe specified entry was not found.

H  %1!-20s!  %2!-20s!  %3!-10s!

XThe interface failed to initialize: %1

XUnable to retrieve ARP information: %1

LThe ARP entry addition failed: %1

LThe ARP entry deletion failed: %1

4No ARP Entries Found.

 Unknown -%0

HIPv4 Protocol is not installed

|4VS_VERSION_INFO��
|O
|O?�StringFileInfo�040904B0LCompanyNameMicrosoft CorporationNFileDescriptionTCP/IP Arp Commandh$FileVersion10.0.20348.1 (WinBuild.160101.0800)0InternalNamearp.exe�.LegalCopyright� Microsoft Corporation. All rights reserved.@OriginalFilenamearp.exe.muij%ProductNameMicrosoft� Windows� Operating System>
ProductVersion10.0.20348.1DVarFileInfo$Translation	�PADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDINGPADDINGXXPADDING